Who's online: Hilly, Drac, Kjay, fatbat, Guests: 328
122/123
  • Roo Ted Posts: 521
    Boganville
    Performance Poster Roo Ted
    19 Jul 2018 08:16 AM
    Daggs I hate to tell you, but I think some arsehole snuck in and pinched most of your bike......
  • Daggs Posts: 2382
    Lower South East, South Aust.
    Motor Head Daggs
    19 Jul 2018 11:11 AM
    Quoting Roo Ted on 19 Jul 2018 08:16 AM
    Daggs I hate to tell you, but I think some arsehole snuck in and pinched most of your bike......
    Ha ha, she’s all there, just in a lot of different boxes, I’ve stripped it completely for a bit of a revamp
  • lucifer_mr2 Posts: 408
    Stage 1 Poster lucifer_mr2
    19 Jul 2018 06:29 PM
    Looks like a big job. Got much planned with the engine?
  • Daggs Posts: 2382
    Lower South East, South Aust.
    Motor Head Daggs
    19 Jul 2018 07:42 PM
    Quoting lucifer_mr2 on 19 Jul 2018 06:29 PM
    Looks like a big job. Got much planned with the engine?
    Bought this for a project, I need something to tinker on and have done all I want to do with my Dyna for now. I aquired this bike quite cheap so prepared to do whatever I have to to get it to a level I'm happy with and happy to split the cases etc on this where I would be hesitant to do that with my Dyna unless it was absolutely necessary.
    So yes, doing a bit with the engine. Once I pulled it down I found the timken main bearings are shot, I Thought I could hear a knock there somewhere so happy I've at least found this.  Also it has a 1200 kit with 1200 heads but bores and slugs quite badly scored...
    All the alloy will get vapor blasted, Will likely be going with the hammer 1275 kit, I have some Andrews V2 cams to go in, will see Mr. Hood again to tidy up the heads, mild porting and whatever we decide to do once I have a chat with him. It has an issue with the gear selector, way too much axial play, so will have a good look at that, maybe get the upgraded clutch basket...
    No intention at all to make this a high performance orientated build, I have something for that already. Just hopefully something that runs well and stands out a bit. There will be a lot of small mods here and there, just a fun little project .

    This pic is how it was when I bought it...
    HD Forums Australia - image_2.jpeg

  • Hilly Posts: 2229
    Townsville
    Motor Head Hilly
    20 Jul 2018 07:25 AM
    Very cool Daggs, get a thread going if you are up to it.
  • Daggs Posts: 2382
    Lower South East, South Aust.
    Motor Head Daggs
    20 Jul 2018 07:32 AM
    Quoting Hilly on 20 Jul 2018 07:25 AM
    Very cool Daggs, get a thread going if you are up to it.
    I will later on Hilly, slow going at the moment, been working away from home for the last 2 months and heading overseas for 5 weeks soon so once I’m back and have progess to report I will!! Taking plenty of pics to put up later
  • Hilly Posts: 2229
    Townsville
    Motor Head Hilly
    20 Jul 2018 09:02 PM
    Quoting Hilly on 20 Jul 2018 07:25 AM
    Very cool Daggs, get a thread going if you are up to it.
    Quoting Daggs on 20 Jul 2018 07:32 AM
    I will later on Hilly, slow going at the moment, been working away from home for the last 2 months and heading overseas for 5 weeks soon so once I’m back and have progess to report I will!! Taking plenty of pics to put up later
    That's the go mate, be cool to have a project that's not the transport
  • Daggs Posts: 2382
    Lower South East, South Aust.
    Motor Head Daggs
    20 Jul 2018 09:35 PM
    Quoting Hilly on 20 Jul 2018 07:25 AM
    Very cool Daggs, get a thread going if you are up to it.
    Quoting Daggs on 20 Jul 2018 07:32 AM
    I will later on Hilly, slow going at the moment, been working away from home for the last 2 months and heading overseas for 5 weeks soon so once I’m back and have progess to report I will!! Taking plenty of pics to put up later
    Quoting Hilly on 20 Jul 2018 09:02 PM
    That's the go mate, be cool to have a project that's not the transport
    Exactly !
  • Hilly Posts: 2229
    Townsville
    Motor Head Hilly
    20 Jul 2018 10:06 PM
    Quoting Daggs on 20 Jul 2018 07:32 AM
    I will later on Hilly, slow going at the moment, been working away from home for the last 2 months and heading overseas for 5 weeks soon so once I’m back and have progess to report I will!! Taking plenty of pics to put up later
    Quoting Hilly on 20 Jul 2018 09:02 PM
    That's the go mate, be cool to have a project that's not the transport
    Quoting Daggs on 20 Jul 2018 09:35 PM
    Exactly !
    5 weeks is a good outing Daggs, enjoy that shit :)
  • Krash Kinkade Posts: 2193
    Motor Head Krash Kinkade
    21 Jul 2018 09:28 AM
    Quoting lucifer_mr2 on 19 Jul 2018 06:29 PM
    Looks like a big job. Got much planned with the engine?
    Quoting Daggs on 19 Jul 2018 07:42 PMedited: 21 Jul 2018 11:18 AM
    Bought this for a project, I need something to tinker on and have done all I want to do with my Dyna for now. I aquired this bike quite cheap so prepared to do whatever I have to to get it to a level I'm happy with and happy to split the cases etc on this where I would be hesitant to do that with my Dyna unless it was absolutely necessary.
    So yes, doing a bit with the engine. Once I pulled it down I found the timken main bearings are shot, I Thought I could hear a knock there somewhere so happy I've at least found this.  Also it has a 1200 kit with 1200 heads but bores and slugs quite badly scored...
    All the alloy will get vapor blasted, Will likely be going with the hammer 1275 kit, I have some Andrews V2 cams to go in, will see Mr. Hood again to tidy up the heads, mild porting and whatever we decide to do once I have a chat with him. It has an issue with the gear selector, way too much axial play, so will have a good look at that, maybe get the upgraded clutch basket...
    No intention at all to make this a high performance orientated build, I have something for that already. Just hopefully something that runs well and stands out a bit. There will be a lot of small mods here and there, just a fun little project .

    This pic is how it was when I bought it...
    HD Forums Australia - image_2.jpeg

    sounds Great Daggs!
  • Birtyyy Posts: 28
    Melbourne
    Stock Poster Birtyyy
    09 Aug 2018 04:06 PM
    HD Forums Australia - IMG_Sportster - Range Rover.jpg

  • brucefxdl Posts: 882
    south west victoria
    Performance Poster brucefxdl
    09 Aug 2018 07:31 PM
    Quoting Birtyyy on 09 Aug 2018 04:06 PM
    HD Forums Australia - IMG_Sportster - Range Rover.jpg

    looks like a good platform,got a story for us birtyyy.?are you going to run a f/brake?
  • Birtyyy Posts: 28
    Melbourne
    Stock Poster Birtyyy
    10 Aug 2018 07:39 AM
    Quoting Birtyyy on 09 Aug 2018 04:06 PM
    HD Forums Australia - IMG_Sportster - Range Rover.jpg

    Quoting brucefxdl on 09 Aug 2018 07:31 PM
    looks like a good platform,got a story for us birtyyy.?are you going to run a f/brake?
    No, haven't had a front brake for a couple of years now, even before I got the spool wheel. I don't miss it. 
    Built the whole bike myself, been through more changes than I can remember. Currently pulled down getting a new horseshoe oil tank, narrow frisco gas tank, taillight, different riser/bar combo and still tossing up whether to keep the sissy bar or not, possibly some more frame modifications.
    Everything I've done to this bike has been to make it skinnier, I live close to the city so lane splitting is absolutely necessary in peak hour. Think my bars are around 15" wide.
  • Mr.Mow Posts: 486
    Melbourne
    Stage 1 Poster Mr.Mow
    10 Aug 2018 01:21 PM
    Quoting Birtyyy on 09 Aug 2018 04:06 PM
    HD Forums Australia - IMG_Sportster - Range Rover.jpg

    Oh fck yeah man! 
    looks bad ass!!
    What headlight you running on that thing?
  • brucefxdl Posts: 882
    south west victoria
    Performance Poster brucefxdl
    10 Aug 2018 07:20 PM
    thanks birtyyy
  • 05Rik Posts: 14
    Stock Poster 05Rik
    17 Sep 2018 05:32 PM
    05 1200R progress pic. 

    D142857A-0ED2-4FEB-AA00-5614240C8A2A.jpeg


  • dyna13 Posts: 68
    Stock Poster dyna13
    17 Sep 2018 08:09 PM
    Quoting 05Rik on 17 Sep 2018 05:32 PM
    05 1200R progress pic. 

    D142857A-0ED2-4FEB-AA00-5614240C8A2A.jpeg


    Love it
  • imoo6170 Posts: 495
    Sydney
    Stage 1 Poster imoo6170
    18 Sep 2018 07:36 AM
    Quoting 05Rik on 17 Sep 2018 05:32 PM
    05 1200R progress pic. 

    D142857A-0ED2-4FEB-AA00-5614240C8A2A.jpeg


    Looking good - what else do you have planned for it
  • Krash Kinkade Posts: 2193
    Motor Head Krash Kinkade
    18 Sep 2018 07:52 AM
    Quoting 05Rik on 17 Sep 2018 05:32 PM
    05 1200R progress pic. 

    D142857A-0ED2-4FEB-AA00-5614240C8A2A.jpeg


    Looks good! what pipes are those? & are the wheels 18"?
  • 05Rik Posts: 14
    Stock Poster 05Rik
    18 Sep 2018 09:30 AM
    Quoting 05Rik on 17 Sep 2018 05:32 PM
    05 1200R progress pic. 

    D142857A-0ED2-4FEB-AA00-5614240C8A2A.jpeg


    Quoting Krash Kinkade on 18 Sep 2018 07:52 AM
    Looks good! what pipes are those? & are the wheels 18"?
    Pipes are custom made, rear rim is a fat spoke 18 inch and was originally attached to a Dyna front hub. Had to use oversized nipples but seems to be holding up ok.  Front wheel is 19 inch off an 03 Dyna. 
122/123
© 2018 - 1.0.4.2